Micromod Micro-DCI: 53SL5100A Single Loop Controller Uživatelský manuál Strana 147
- Strana / 152
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Single Loop Process Controller Instruction Manual
Database 139
ANI1
Engineering
Zero
ZERO C277 0
This is the lower range value of analog input 1.
ANI0
Calibrate
Span
CIS C296
This is the calibration span adjustment. This parameter is
factory set and should not need adjustment under
normal operation. See Section 12.3 for adjustment.
ANI1
Calibrate
Span
CIS C297
This is the calibration span adjustment. This parameter is
factory set and should not need adjustment under
normal operation. See Section 12.3 for adjustment.
ANO0
Calibrate
Span
COS C300
This is the calibration span adjustment. This parameter is
factory set and should not need adjustment under
normal operation. See Section 12.3 for adjustment.
Parameter
Point 1
Designator
PDA F087 C106
value
A database datapoint whose contents will be displayed
under the Point 1 Name (e.g., C103 to display the Alarm
Limit 1 setting) of the parameter display.
Parameter
Point 2
Designator
PDB F088 C107
value
A database datapoint whose contents will be displayed
under the Point 2 Name (e.g., C104 to display the Alarm
Limit 2 setting) of the parameter display.
Parameter
Point 3
Designator
PDC F089 C108
value
A database datapoint whose contents will be displayed
under the Point 3 Name (e.g., C105 to display the Alarm
Dead Band) of the parameter display.
ANI0 Input
(Display
Only)
ANI H000 0
This is the value in engineering units of the measured
input for ANI0 after all signal conditioning has been
applied.
ANI1 Input
(Display
Only)
ANI H001 0
This is the value in engineering units of the measured
input for ANI1 after all signal conditioning has been
applied.
CCI Input
(Display
Only)
CCI L000 0
When open, a 4 - 24 V dc input signal = 0 when IINV = 0.
When open, a 4 - 24 V dc input signal = 1 when IINV = 1.
When closed, a < 1 V dc input signal = 1 when IINV = 0.
When closed, a < 1 V dc input signal = 0 when IINV = 1.
CCO Output
(Display
Only)
CCO L024 0
If CCO = 0 and OINV = 0, then it is open.
If CCO = 0 and OINV = 1, then it is closed.
If CCO = 1 and OINV = 0, then it is closed.
If CCO = 1 and OINV = 1, then it is open.
Control
Action
RSW L106 1
When set to a 0, the controller output increases as the
process value increases.
When set to a 1, the controler output decreases as the
process value increases.
Table C-2. Database (Continued)
Title Symbol Datapoint Default Attribute
- INSTRUCTION MANUAL 1
- MicroMod Automation, Inc 2
- TABLE OF CONTENTS 3
- LIST OF FIGURES 6
- LIST OF TABLES 7
- 1.0 Introduction 9
- Introduction 3 11
- 1.2 Model Number Breakdown 12
- 1.3 Specifications 13
- 2.0 Installation 17
- Installation 11 19
- Figure 2-3. Intercase Spacing 20
- 2.4 Connections 21
- 2.5 Grounding 23
- 16 Installation 24
- Installation 17 25
- 18 Installation 26
- 3.0 Front Panel 27
- Front Panel 21 29
- Figure 3-6. Alarm Overlay 30
- 3.3 Front Panel Pushbuttons 31
- 24 Front Panel 32
- 3.3.1 Displaying a Datapoint 36
- 3.3.2 Altering a Datapoint 37
- ∆ = space 38
- 3.3.3 Defaulting the Database 39
- Figure 3-14. The KEY? Prompt 42
- Front Panel 35 43
- C & H 45
- A & Q 45
- TRL-C aborts the operation 46
- 40 Front Panel 48
- 4.0 Configuration Parameters 49
- Figure 4-1. ANIO/1 53
- Figure 4-2 53
- Figure 4-3. CCI0 55
- Figure 4-4. CCO0 55
- CCO L024 0 56
- OINV L288 0 56
- COTAG A280 CCO0 56
- AIX ■ ● ▲ ◆ B335 1 57
- RSW ■ ● ▲ ◆ L106 1 57
- Table 4-11. System Module 61
- Table 5-8. System Module 71
- 6.0 Analog Backup Controller 73
- Table 6-1 75
- Table 6-8. System Module 81
- 7.0 Ratio (PID) Controller 83
- Table 7-1 85
- Table 7-7. System Module 91
- 8.0 Automatic/Manual Station 93
- Table 8-1 95
- Table 8-8. System Module 101
- 9.0 Parameter Display 103
- 96 Parameter Display 104
- 98 Parameter Display 106
- 10.0 Instrument Tuning 107
- 10.3 Derivative Action (TD) 108
- 10.4 Instrument Tuning 108
- 11.0 EASY-TUNE 111
- 11.3 EASY-TUNE Parameters 112
- 108 Easy-Tune 116
- 110 Easy-Tune 118
- 112 Easy-Tune 120
- 12.0 Maintenance 121
- 12.3 Calibration 122
- 12.5 Resetting the Controller 123
- 12.6 Parts List 124
- 12.7 Supplemental Information 124
- Maintenance 117 125
- 118 Maintenance 126
- Maintenance 119 127
- 120 Maintenance 128
- Appendix B: Communications 133
- B.1.1 Configuration 134
- B.1.2 Protocol 135
- B.1.3 Message Types 136
- B 200H 1 138
- L 500H 1 Bit 138
- C 600H 3 138
- Appendix C: Database 141
- Table C-2. Database 142
- CIZ B264 144
- AIX B335 1 145
- ANO0 C000 0 145
- PV C100 0 145
- P or DOWN arrow pushbuttons 146
- 142 Database 150
Související produkty a manuály pro Zařízení Micromod Micro-DCI: 53SL5100A Single Loop Controller
Zařízení Micromod MOD: 30ML and Modcell Totalization Application Gui Uživatelský manuál
(24 stránky)
(24 stránky)
Zařízení Micromod MOD: MODCELL Multiloop Processor 2002N Model C and Uživatelský manuál
(82 stránky)
(82 stránky)
Zařízení Micromod MOD: 30ML and Modcell Maintenance for 2001N, 2002N Uživatelský manuál
(152 stránky)
(152 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.231 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce